2016年7月18日星期一

Tacho Pro 2008 July PLUS Universal Dash Programmer Odometer Correction on Citroen Model Xsara

Tacho Pro 2008 July PLUS Universal Dash Programmer Odometer Correction on Citroen Model Xsara

Preparation:

Tacho Pro 2008 July PLUS Universal Dash Programmer

Use this board and clip:



Operation Steps:

• Remove the cluster and open it.
• Remove the motors carefully from the circuit board. Do not pull off the needles!!!
• Look for the 8 pin chip 93C46.
• Look for the silver chrystal and join its contacts.
• Connect the clip to Port 1.
• Put the clip on the chip 93C46 (red on pin 1).
• Select the menu: Citroen-Xsara
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

2016年7月6日星期三

Tacho Pro 2008 July PLUS Universal Odometer Correction on Ford Focus Step by Step

Tacho Pro 2008 July PLUS Universal Odometer Correction on Ford Focus Step by Step

Tacho Pro 2008 July PLUS Universal is one French favorite device to do mileage correction. It can do multi-brand cars than the other tool. See the procedure to do on Ford Focus bellow:

Use the Scorpio plug:


26pin white port

1.Pin 2      GND(-)          black
2.Pin 9      RX (Data)       blue
3.Pin 11     TX (Data)       yellow
4.Pin 14     12V (+)         red
5.Pin 16     12V (+)         red

Processor version 1:
• Connect Pin 1 ( left side down) and pin 2 (right from pin 1), or connect black to test point 3 (TP3).



Processor version 2:
• Connect pin 1 (middle upside) and pin 2 (left beside pin 1), or connect black to testpoint 46 (TP46).


• Remove the cluster and open it.
• Connect the cables as shown in the picture.
• Select the menu Ford-Focus
• The Tacho Pro 2008 July PLUS Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

2016年6月20日星期一

Tacho Pro 2008 July PLUS Universal Dash Programmer UNLOCK on BMW Model 5 series E34 after 3/1989

Tacho Pro 2008 July PLUS Universal Dash Programmer UNLOCK on BMW Model 5 series E34 after 3/1989

Prepare: Tacho Pro 2008 July Plus Universal

Board for brown and blue code plug:




board for green code plug:




1. Remove the cluster.
2. Look on the rear for a small plastic cover. Under it you can see a brown, blue or green code plug. You have to break this cover to get the code plug out.
3. Take the code plug out.
4. Put the brown or blue code plug on port 1. The pins of the code plug are marked on the bottom in the plastic. Pin 1 of the code plug must be positioned on pin 1 of the board.
5. If the code plug is green, put it on the board “BMW green”. There you can also see the shape of the code plug Put the plug carefully on the socket.
6. Select the menu BMW-5er/7er-blue
or BMW-5er/7er-brown
or BMW 5er/7er-green
7. The Tacho Pro 2008 Universal shows you the old value.
8. Select the menu Adjust KM.
9. Enter the new value.
10. Verify the new value with OK.

Brown code plug:


2016年6月16日星期四

Tacho Pro 2008 July PLUS Mileage Change on Chrysler Stratus after model 1999

Tacho Pro 2008 July PLUS Mileage Change on Chrysler Stratus after model 1999

Use this plug:


• The diagnostic port is near your left knee when you sit on the driver's seat. Turn ignition on.
• Connect the Tacho Universal to Chrysler diagnostic plug and the diagnostic port. Use the connector CCD.
• Select the menu Chrysler-Chrysler99 Diagnosis.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

Note: If the new value is not displayed, you have to disconnect the battery for about 2 minutes.

2016年5月5日星期四

10 Steps For Tacho Pro 2008 Universizl Correct Audi A3/S3 UKNSI Mileage

10 Steps For Tacho Pro 2008 Universizl Correct Audi A3/S3 UKNSI Mileage

Tacho Universal is the most sold programming-device for digital speedometers worldwide.support multi-language. It provides the latest significant hardware and software performance enhancements over the diagnostic tools.You can serve almost any vehicle with the Tacho Universal.

Operation Tips

1.Remove the cluster and open it.
2.Look for the 8 pin chip 93C56 (not the chip 93C46).
3.Look for the silver chrystal and join its contacts.
4.Connect the clip to Port 1.
5.Put the clip on the chip 93C56 (red on pin 1).
6.Select the menu Audi-A3-UK NSI-Clip.
7.The Tacho Universal shows you the old value.
8.Select the menu Adjust KM.
9.Enter the new value.

10.Verify the new value with OK.

Related FAQ

Q: I have car 02 escalade, and when I connect Tacho Pro 2008 July plus to the car, it prompts to enter Clip Number on the EEprom 95020 and then click to confirm.
A: To find out eeprom 95020 chip in the dashboard.
Q: Does it need password when the Tacho pro 2008 power on?

A: No, it doesn't need.

Tacho Accessories:







2016年4月28日星期四

Usage for the Tacho Pro 2008 Universal Correct Audi Model A3 / S3 VDO before model 2000

Usage for the Tacho Pro 2008 Universal Correct Audi Model A3 / S3 VDO before model 2000

Tacho pro 2008 Description:

Tacho Universal is the most sold programming-device for digital speedometers worldwide. The system is a high-quality tool, which offers a maximum of flexibility and working comfort despite simplest operation.
You can serve almost any vehicle with the Tacho Universal.

The OBD II -plug needed:


Opreation Instruction: 

Turn ignition on.
• Connect the Tacho Universal to the OBD II plug and the diagnostic port.
• Select the menu AUDI-A3-VDO-Diagnosis.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK

2016年4月27日星期三

How to use Tacho Pro 2008 Universal to Correct Audi Model A2 VDO Mileage?

How to use Tacho Pro 2008 Universal to Correct Audi Model A2 VDO Mileage?

Tools need: Tacho Pro 2008 Universal
Board and clip needed:


Opreation Instruction: 

Step 1: Remove the cluster and open it.
Step 2: Look for the 8 pin chip 93C86.
Step 3: Look for the silver chrystal and join its contacts.
Step 4: Connect the clip to Port 0.
Step 5: Put the clip on the chip 93C86 (red on pin 1).
Step 6: Select the menu Audi-A3-A3 2000- clip 2000.
Step 7: The Tacho Pro 2008 Universal shows you the old value.
Step 8: Select the menu Adjust KM.
Step 9: Enter the new value.
Step 10: Verify the new value with OK.